Dell 3110 Color Laser Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 451

background image

Replace the tray into the printer.

3.

Replacing the Belt Unit

CAUTION:

Before performing any of the following procedures, read and follow the safety

instructions in your

Owner's Manual

.

NOTICE:

Make sure nothing touches or scratches the surface (black-colored film) of the belt unit.

Scratches, dirt, or oil from your hands on the film of the belt unit may reduce print quality.

NOTICE:

To protect the drums of the print cartridges against bright light, close the front cover within

5 minutes. If the front cover remains open for more than 5 minutes, print quality may deteriorate.

Dell belt units are available only through Dell. To order by phone, see your

Owner's Manual

. Dell

recommends Dell belt units for your printer. Dell does not provide warranty coverage for problems caused by
using accessories, parts, or components not supplied by Dell.

Removing the Used Belt Unit

NOTE:

Remove any print jobs from the center output tray, and close the multipurpose feeder cover

before opening the front cover.

Make sure that the printer is turned off.

1.

Push the side button and open the front cover.

2.

«
...
316
317
318
319
320
...
»

Содержание 3110 Color Laser




































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3110 Color Laser

Power Defense PD3

Бренд: Eaton Страницы: 4

Бренд: iFactory3D Страницы: 39

Бренд: Lanier Страницы: 6

Бренд: Chamjin I&C Страницы: 21

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 34

Бренд: Oki Страницы: 65

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 36

Бренд: OHAUS Страницы: 28

Бренд: Oce Страницы: 396

Бренд: Oce Страницы: 28

Бренд: Oki Страницы: 64

Бренд: Xerox Страницы: 9

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды