Dell 3110 Color Laser Скачать руководство пользователя страница 145

Страница: 145 / 451

FTP

Enable*

Enables the FTP port.

Disable

Disables the FTP port.

NetWare*

NetWare IP Enable*

Uses IP for NetWare.

Disable

Does not use IP for NetWare.

NetWare
IPX

Enable*

Uses IPX for NetWare.

Disable

Does not use IPX for NetWare.

WSD

Enable*

Enables the WSD port.

Disable

Disables the WSD port.

SNMP

SNMP UDP

Enable*

Enables the UDP.

Disable

Disables the UDP.

SNMP
IPX*

Enable*

Enables the IPX.

Disable

Disables the IPX.

E-Mail Alert

Enable*

Enables the E-Mail Alert feature.

Disable

Disables the E-Mail Alert feature.

EWS

Enable*

Enables an access to

Dell Printer Configuration Web Tool

embedded in the printer.

Disable

Disables an access to

Dell Printer Configuration Web Tool

embedded in the printer.

AppleTalk*

Enable*

Enables the AppleTalk port.

Disable

Disables the AppleTalk port.

Bonjour(mDNS)*

Enable*

Enables the Bonjour(mDNS) port.

Disable

Disables the Bonjour(mDNS) port.

Содержание 3110 Color Laser




































































































































































































































































































































































































































































Результаты поиска

Содержание 3110 Color Laser

Отзывы:

Похожие инструкции для 3110 Color Laser

Бренды по названию

Популярные бренды

Dell 3110 Color Laser, Руководство пользователя

Результаты поиска

Содержание 3110 Color Laser

Отзывы:

Похожие инструкции для 3110 Color Laser

Бренды по названию

Популярные бренды