Dell 3110 Color Laser Скачать руководство пользователя страница 446

Страница: 446 / 451

technical standards:

EN 55022 -

Information Technology Equipment - Radio Disturbance Characteristics - Limits and

Methods of Measurement

EN 55024 -

Information Technology Equipment - Immunity Characteristics - Limits and Methods of

Measurement

EN 61000-3-2 -

Electromagnetic Compatibility (EMC) - Part 3: Limits - Section 2: Limits for Harmonic

Current Emissions (Equipment Input Current Up to and Including 16 A Per Phase)

EN 61000-3-3 -

Electromagnetic Compatibility (EMC) - Part 3: Limits - Section 3: Limitation of

Voltage Fluctuations and Flicker in Low-Voltage Supply Systems for Equipment With Rated Current Up
to and Including 16 A

EN 60950 -

Safety of Information Technology Equipment

NOTE:

EN 55022 emissions requirements provide for two classifications:

Class B is for typical domestic areas.

This Dell device is classified for use in a typical Class B domestic environment.

Declaration of Conformity

in accordance with the preceding directives and standards has been made and is

on file at Dell Inc. Products Europe BV, Limerick, Ireland.

CE Mark Notice

This equipment complies with the essential requirements of the European Union Directive 1999/5/EC.

Содержание 3110 Color Laser




































































































































































































































































































































































































































































Результаты поиска

Содержание 3110 Color Laser

Отзывы:

Похожие инструкции для 3110 Color Laser

Бренды по названию

Популярные бренды

Dell 3110 Color Laser, Руководство пользователя

Результаты поиска

Содержание 3110 Color Laser

Отзывы:

Похожие инструкции для 3110 Color Laser

Бренды по названию

Популярные бренды