Dell 3110 Color Laser Скачать руководство пользователя страница 279

Страница: 279 / 451

Setup Security

Press

Menu

Press

until

Printer Setting

appears, and then press

Press

until

Printer Settings

appears, and then press

Press

until

Security Settings

appears, and then press

Security Settings is displayed.

To set or change the password to limit access to the menus from the operator panel.

Set the password of the

Dell Printer Configuration Web Tool

from

Set Password

Print Server

Settings

Values:

Panel Lock

Specifies whether to limit access to the menus.

Change Password

Sets a password to limit access to the menus.

Re-enter Password

Type the new password again to confirm.

NOTE:

This menu sets a password to lock the operator panel. When changing the password for the

Dell Printer Configuration Web Tool

, click

Set Password

on the left frame and set the password.

Troubleshooting Instructions

Use the Customer Mode to locate the unit in the printer that causes a problem.

Diagnostic Menu Map (Customer Mode)

Turn off the printer.

Turn on the printer while holding down

and

The Customer Mode menu appears.

Содержание 3110 Color Laser




































































































































































































































































































































































































































































Результаты поиска

Содержание 3110 Color Laser

Отзывы:

Похожие инструкции для 3110 Color Laser

Бренды по названию

Популярные бренды

Dell 3110 Color Laser, Руководство пользователя

Результаты поиска

Содержание 3110 Color Laser

Отзывы:

Похожие инструкции для 3110 Color Laser

Бренды по названию

Популярные бренды