Dell 3110 Color Laser Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 451

background image

Color Test Page

Purpose:

To print a page for testing colors.

Stored Document

Purpose:

To print a list of all files that are stored as Secure, Store, and Proof Print in the RAM disk.

NOTE:

The Stored Print menu is only displayed when 256 MB or more of optional memory card is

installed on the printer.

Admin Menu

Use the

Admin Menu

menu to configure a variety of printer features.

Wired Network

Use the

Wired Network

menu to change printer settings affecting jobs sent to the printer through the wired

network.

NOTE:

Values marked by an asterisk (*) are the factory default menu settings.

Ethernet

Purpose:

To specify the communication speed and the duplex settings of Ethernet. The change becomes effective after
the printer is turned off and then on again.

Values:

«
...
140
141
142
143
144
...
»

Содержание 3110 Color Laser




































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3110 Color Laser

Бренд: Fenix Imvico Страницы: 88

7300DX - Phaser Color Laser Printer

Бренд: Xerox Страницы: 14

Бренд: Olivetti Страницы: 16

Бренд: Konica Minolta Страницы: 32

Бренд: Konica Minolta Страницы: 35

WorkCentre 7655

Бренд: Xerox Страницы: 24

Бренд: Oki Страницы: 40

Бренд: Oce Страницы: 90

Бренд: Xante Страницы: 31

Бренд: Oki Страницы: 192

Бренд: Oki Страницы: 57

Бренд: Axis Страницы: 66

Бренд: Planmeca Страницы: 56

Бренд: WANHAO Страницы: 18

Бренд: M&R Страницы: 36

BROTHER HL-630 OPC

Бренд: Summit Страницы: 46

Бренд: Source Technologies Страницы: 47

Бренд: Unisys Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды