manualshive.com logo in svg

COSMOGAS Adveco MYDENS 15B, Инструкция по установке, использованию и техническому обслуживанию

Инструкции по установке, использованию и техническому обслуживанию для продукта COSMOGAS Adveco MYDENS 15B можно скачать бесплатно с нашего сайта. Ознакомьтесь с руководством перед началом эксплуатации. Узнайте больше о продукте и его функциях, загрузив мануал с manualshive.com.

Поделиться
Скачать
background image

2

CONTENTS

MYDENS

COSMOGAS

1 - GENERAL SAFETY WARNINGS ....................................................................................................................................................... 4

1.1 - National installation laws .......................................................................................................................................................... 5

2 - GENERAL INFORMATION ................................................................................................................................................................ 6

2.1 - Introduction .............................................................................................................................................................................. 6

2.2 - Manufacturer ............................................................................................................................................................................ 6

2.3 - Overview of the models ........................................................................................................................................................... 6

2.4 - Accessories .............................................................................................................................................................................. 6

2.5 - Meaning of symbols used ........................................................................................................................................................ 7

2.6 - Maintenance ............................................................................................................................................................................ 7

2.7 - Disposal ................................................................................................................................................................................... 7

3 - MAIN COMPONENTS ........................................................................................................................................................................ 8

4 - OPERATION .................................................................................................................................................................................... 10

4.1 - Operation and intended use ................................................................................................................................................... 12

4.2 - Water pressure drops curve ................................................................................................................................................... 13

4.3 - Domestic hot water pressure drops curve ............................................................................................................................. 13

5 - INSTALLATION ................................................................................................................................................................................ 14

5.1 - Packaging opening ................................................................................................................................................................ 14

5.2 - Dimensions and minimum safety distances ........................................................................................................................... 14

5.3 - Choosing the installation place .............................................................................................................................................. 14

5.4 - Supply and return ................................................................................................................................................................... 15

5.4.1 - Checking and treating the heating water/filling and supplementary water

 ............................................................... 15

5.5 - Low-temperature systems ...................................................................................................................................................... 17

5.6 - Domestic hot and cold water .................................................................................................................................................. 17

5.7 - Gas ........................................................................................................................................................................................ 17

5.9 - Condensate drain pipe ........................................................................................................................................................... 18

5.10 - Safety valve ......................................................................................................................................................................... 19

5.11 - Hydraulic and gas connections, and mounting of the bottom cover ..................................................................................... 19

5.12 - Hydraulic connections for model -- B ................................................................................................................................... 20

5.13 - Water softener (on request) ................................................................................................................................................. 20

5.14 - Electrical connections: details .............................................................................................................................................. 21

5.14.1 - Power main electrical supply .................................................................................................................................. 22

5.14.2 - Choosing the room thermostat/chronothermostat .................................................................................................. 22

5.14.3 - Installation of  the room thermostat/chronothermostat ........................................................................................... 22

5.14.4 - Connecting the room thermostat/chronothermostat ............................................................................................... 22

5.14.5 - CR04 remote time control (on request) .................................................................................................................. 23

5.14.6 - Installing the outdoor temperature sensor (on request) ......................................................................................... 23

5.14.7 - 0-10 VDC type dialogue ......................................................................................................................................... 24

5.14.8 - Alarm output ........................................................................................................................................................... 24

5.15 - Connection and setting of the appliance in cascade. ........................................................................................................... 25

5.16 - Connecting the appliance to a tank with coil ........................................................................................................................ 27

5.16.1 - Anti-legionella ......................................................................................................................................................... 27

5.17 - Flue exhaust and air intake ducts ........................................................................................................................................ 28

5.17.1 - Type of intake/exhaust B23 and B23P ................................................................................................................... 29

5.17.2 - “Split 80/80PP” system (polypropylene) (type C43; C53; C83; C93) ..................................................................... 30

5.17.3 - "Split 80/80PP” system: accessories available ...................................................................................................... 31

5.17.4 - “Split 80/80PP” system: installation examples ....................................................................................................... 32

5.17.5 - “60/100PP Vertical coaxial” system (polypropylene) (Type C13; C33) ................................................................... 33

5.17.6 - “60/100PP Horizontal coaxial” system (polypropylene) (Type C13; C33) .............................................................. 34

5.17.7 - “60/100PP Coaxial” system: accessories available ................................................................................................ 35

5.17.8 - “60/100PP Coaxial” system: installation examples ................................................................................................ 36

5.17.9 - “80PP single” system (polypropylene) (Type "B23" or "B23P") .............................................................................. 37

5.17.10 - “80PP Single” system: accessories available ....................................................................................................... 37

6 - START-UP ........................................................................................................................................................................................ 38

6.1 - Start-Up .................................................................................................................................................................................. 38

6.1.1 - Instructions to the user ............................................................................................................................................. 38

6.1.2 - Filling the condensate drain siphon .......................................................................................................................... 38

6.1.3 - Filling the central heating system ............................................................................................................................. 39

6.2 - General recommendations regarding the gas supply ............................................................................................................ 39

6.3 - Type of gas for which the appliance is set ............................................................................................................................. 39

6.4 - Conversion of the appliance from one type of gas to another ............................................................................................... 40

6.5 - Ignition ................................................................................................................................................................................... 42

6.6 - Check the supply gas pressure .............................................................................................................................................. 42

6.7 - Controlling the level of CO2 and any adjustments ................................................................................................................. 43

6.8 - Adjusting the power in central heating mode (Range Rated) ................................................................................................. 44

6.9 - Adjusting the domestic hot water flow rate

 ............................................................................................................................. 44

7 - USE .................................................................................................................................................................................................. 45

7.1 - Checking the valve opening ................................................................................................................................................... 46

7.2 - Checking the central heating system pressure ...................................................................................................................... 46

Содержание Adveco MYDENS 15B

































































































Отзывы:

Нет отзывов

Похожие инструкции для Adveco MYDENS 15B

IDEAL F400 Installation And Servicing preview
F400
Бренд: IDEAL Страницы: 60
Vaillant ecoTEC exclusive SERIES Installation And Maintenance Instructions Manual preview
ecoTEC exclusive SERIES
Бренд: Vaillant Страницы: 48
Connerton Co RLRB-A Installation And Operating Insctructions preview
RLRB-A
Бренд: Connerton Co Страницы: 4
Alpha Boilers SY9-24 Installation And Servicing Instructions preview
SY9-24
Бренд: Alpha Boilers Страницы: 32
Baxi EcoBlue 12 Heat ErP Installation And Service Manual preview
EcoBlue 12 Heat ErP
Бренд: Baxi Страницы: 64
Biasi M90E.24S Service Manual preview
M90E.24S
Бренд: Biasi Страницы: 44
Kober C38GC25 User Manual preview
C38GC25
Бренд: Kober Страницы: 37
Bryan Boilers FF1000 Installation & Operation Manual preview
FF1000
Бренд: Bryan Boilers Страницы: 85
Palazzetti CT 14 Installation, User And Maintenance Manual preview
CT 14
Бренд: Palazzetti Страницы: 140
Palazzetti CALDAIA A PELLET JP Application. Installation And Maintenance Manual preview
CALDAIA A PELLET JP
Бренд: Palazzetti Страницы: 140
CAC / BDP BW4BAH-105 Installation, Operation & Maintenance Manual preview
BW4BAH-105
Бренд: CAC / BDP Страницы: 32
Potterton Performa 24 Installation And Servicing Instructions preview
Performa 24
Бренд: Potterton Страницы: 32
Burnham Alpine ALP080 Installation, Operating And Service Instructions preview
Alpine ALP080
Бренд: Burnham Страницы: 132
Unical AIREX 25 2S Installation And Servicing Manual preview
AIREX 25 2S
Бренд: Unical Страницы: 40
Savio GAIA 424 RS Service Manual preview
GAIA 424 RS
Бренд: Savio Страницы: 48
Unical Alkon 09 R 18 User Operating Instructions Manual preview
Alkon 09 R 18
Бренд: Unical Страницы: 8
Wahl Bach UTS15 User Manual preview
UTS15
Бренд: Wahl Bach Страницы: 48
ECR Utica Heating UH15B-060K Installation, Operation & Maintenance Manual preview
Utica Heating UH15B-060K
Бренд: ECR Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды