COSMOGAS Adveco MYDENS 15B Скачать руководство пользователя страница 87

Страница: 87 / 96

MYDENS

COSMOGAS

8 - MAINTENANCE

8.22 - Checking the ionisation current

1. - Power up the appliance and open the gas supply;

2. - Switch on the appliance;

3. - Press the RESET button;
4. - The display shows parameter

0.000

;

5. - Press the button

up to the parameter

1.000

;

6. - Press the RESET button;
7. - Scroll through the parameters using the keys

and

;

8. - The ionisation current value can be consulted at

parameter

1.008

;

9. - Check that it is within the values from 4 to 7 µA;

8.23 - Checking combustion efficiency

1. - Check and adjust the CO2 (section 6.7);

2. - Check the combustion efficiency at full load with

maximum flow temperature for the type of system you

are servicing;

3. - Check that the measured value is higher than the

regulatory requirements;

8.24 - Water temperature measurement

sensors

Various temperature sensors are positioned on the heat

exchanger. The electrical resistance between the two

sensor contacts must correspond to Figure 75.
The temperature sensors are:

1001

1002

1005

1006

and

1007

, verify their positioning in Figures 1

and 2.

Figure 75

8.25 - Outdoor temperature sensor

On request, the outdoor temperature sensor can be
connected to the appliance

1004

(see section 5.14.6).

The electrical resistance between the two sensor contacts

must correspond to Figure 76.

Figure 76

Содержание Adveco MYDENS 15B

































































































Результаты поиска

Содержание Adveco MYDENS 15B

Отзывы:

COSMOGAS Adveco MYDENS 15B, Инструкция по установке, использованию и техническому обслуживанию, Страница: 87 / 96

Результаты поиска

Содержание Adveco MYDENS 15B

Отзывы: