COSMOGAS Adveco MYDENS 15B Скачать руководство пользователя страница 65

Страница: 65 / 96

MYDENS

COSMOGAS

7 - USE

Lock

Lock description

Checks

Solutions

Loc 10 E2prom memory parameters incorrect

Replace the control board.

Loc 11 Software error on the control board

Replace the control board.

Loc 12 Software error on the control board

Replace the control board.

Loc 13 Software error on the control board

Replace the control board.

Loc 14 Software error on the control board

Replace the control board.

Loc 15 Flue gas fuse

Check that the high limit flue gas

temperature fuse (detail "18" of Figure 2) has

not been triggered.

If the flue gas temperature fuse has been

triggered (the contact is open), before

replacing it, carefully check the appliance

efficiency as detailed in section 8.23;

WARNING!!! If the efficiency is not within

the specified limits DO NOT ATTEMPT

TO RESET THEM, but contact the

manufacturer.

The supply temperature exceeds 105°C with

the gas valve closed

Check that the electrical resistance of the

two supply sensors (detail "35" of Figure 2)

matches the graph in section 8.24.

If one of the two sensors does not match, the

double supply sensor must be replaced.

Check that the gas valve closes the gas

correctly when the burner switches off.

The gas valve must be replaced if it does not

close correctly.

Exchanger malfunction

Check that the primary heat exchanger

temperature fuse (detail "54" of Figure 2) has

not intervened.

If the primary heat exchanger temperature

fuse has intervened (the contact is open),

the exchanger must be replaced.

Loc 16 Flue gas maximum temperature.

WARNING!!! If the lock is repeated more

than once a day, switch-off the appliance

and contact a qualified service centre.

NOT ATTEMPT TO REPAIR THE

APPLIANCE.

Check there is no air in the central heating

circuit; bleed the highest radiators.

Bleed the air from the appliance and from

the highest central heating elements with

respect to the appliance.

Check the pump is operating correctly.

If the pump is not working, it must be

replaced.

Check that the flue gas temperature is

not more than 30°C above the return

temperature.

If the difference between the return

temperature and the flue gas temperature

is above 30°C, contact a qualified service

centre.

Measure the appliance efficiency, it must

correspond to value declared in the technical

features.

If the efficiency does not correspond to the

data at the end of the manual, the primary

heat exchanger is probably dirty from the

flue gas side or the water side. Clean and

check efficiency again.

Loc 17 Software error on the control board

Replace the control board.

Loc 18 Software error on the control board

Replace the control board.

Loc 19 Software error on the control board

Replace the control board.

Loc 20 Flame present 10 seconds after gas valve is

closed

Replace the gas valve or the control board.

Loc 21 Flame present before ignition

Replace the gas valve or the control board.

Содержание Adveco MYDENS 15B

































































































Результаты поиска

Содержание Adveco MYDENS 15B

Отзывы:

Похожие инструкции для Adveco MYDENS 15B

Бренды по названию

Популярные бренды

COSMOGAS Adveco MYDENS 15B, Инструкция по установке, использованию и техническому обслуживанию

Результаты поиска

Содержание Adveco MYDENS 15B

Отзывы:

Похожие инструкции для Adveco MYDENS 15B

Бренды по названию

Популярные бренды