Cognex In-Sight 1721 Скачать руководство пользователя | Manualshive

Страница: 64 / 156

background image

Section 6: System Settings

In-Sight

®

1700 Series Wafer Reader

54

6.2 Version Information

The

Info

tab shows important information about your wafer reader and its current

firmware and applet version. This information is needed if assistance is ever required
from Cognex Technical Support. The Online checkbox at the top-right of the Run tab
switches the wafer reader between its Online and Offline modes of operation. For more
information about the Online checkbox, see Section 5.1.1. The Back hyperlink, located
below the Online checkbox, returns you to the Run tab.

Figure 6-1: Info Tab

6.3 Configuring Network Settings

The

Network

tab (Figure 6-2) configures an In-Sight wafer reader to be used on a

network.

Figure 6-2: Network Tab

Use DHCP Server

The Use DHCP Server checkbox determines whether the wafer reader uses DHCP
(Dynamic Host Configuration Protocol) on start up or if the values in the Network tab
configure TCP/IP.

NOTE

This box should be checked only if a DHCP server is running on the local network. If the box is

checked and a DHCP server does not respond within 60 seconds, the wafer reader will boot
without network support enabled.

«
...
62
63
64
65
66
...
»

Содержание In-Sight 1721





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для In-Sight 1721

Бренд: CAME Страницы: 2

Бренд: N-Com Страницы: 28

Бренд: Hama Страницы: 40

Бренд: Rave Sports Страницы: 16

Бренд: Hard Head Страницы: 40

Бренд: Harbor Freight Tools Страницы: 7

Бренд: Racing Страницы: 13

Бренд: M-Audio Страницы: 14

Бренд: Yakima Страницы: 8

Бренд: YachtSafe Страницы: 4

Бренд: ICON Страницы: 2

Power commander GSXR750

Бренд: Dynojet Страницы: 4

Soft Luggage Pannier Racks

Бренд: Honda Страницы: 10

Бренд: Paxton Automotive Страницы: 85

Бренд: Thule Страницы: 8

CARPOWER CAP-12XHQ

Бренд: Monacor Страницы: 5

USB 3.0 Dual Head Docking Station

Бренд: SIIG Страницы: 12

Бренд: Thunderbike Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды