Cognex In-Sight 1721 Скачать руководство пользователя

Страница: 116 / 156

Section 8: Specifications

In-Sight

1700 Series Wafer Reader

106

8.2 I/O Specifications

The In-Sight wafer reader features one built-in acquisition trigger input and two user-
configurable LED outputs for general-purpose use.

8.2.1 Breakout Port Pin Assignments

Table 8-4 lists the pin assignment for each of the 8 signal lines of the Breakout Port
(labeled “24VDC”) according to each method of access.

Table 8-4: Breakout Port Pin Assignments

IN-SIGHT BREAKOUT

PORT PIN

SIGNAL

BREAKOUT CABLE

WIRE COLOR

BREAKOUT MODULE*

TERMINALS

+24VDC

White/Green

6, 8, 10, 12, 14, 15, 16 (+24V)

Green

5 (TRG+)

Trigger –

White/Orange

4 (TRG-)

4 CTS

Blue

RS-232 serial (9-pin DSUB

connector)

5 RTS

White/Blue

RS-232 serial (9-pin DSUB

connector)

6 Serial

Receive

Orange

RS-232 serial (9-pin DSUB

connector)

7 Serial

Transmit

White/Brown

RS-232 serial (9-pin DSUB

connector)

Ground

Brown

1, 2, 3 (GND)

* Refer

the

In-Sight Breakout Module Installation and Reference

(P/N 597-0008-xx) for more detailed information.

NOTE

Unused bare wires can be clipped short or tied back using a tie made from non-conductive
material. Keep all bare wires separated from the +24VDC (White/Green) wire.

Содержание In-Sight 1721





























































































































































Результаты поиска

Содержание In-Sight 1721

Отзывы:

Похожие инструкции для In-Sight 1721

Бренды по названию

Популярные бренды

Cognex In-Sight 1721, Руководство пользователя

Результаты поиска

Содержание In-Sight 1721

Отзывы:

Похожие инструкции для In-Sight 1721

Бренды по названию

Популярные бренды