CanyCom CMX 227 страница 55 Скачать руководство пользователя

Страница: 55 / 103

-47-

Maintenance

Item

Description

Schedule

Note

PSI

Mon

Year

Drive T

rain

V-belt

Belt tension shall be properly adjusted.

√ √

Belt shall be free of damage or excessive
wear.

√ √

Parking Brake

Brake shall work properly.

√ √ √

Page 70

Parking brake shall be able to hold the
machine on the 20-degree slope.

√ √

Steering

Turn steering wheel right and left; front
wheels shall turn accordingly.

√ √

Steering can be adjusted in 5 positions and
locked securely.

√ √

Rods, Links,
and Wires

Rods, links, and wires in linkage shall be free
of deformation or damage.

√ √

Connections shall be free of looseness,
excessive play, or missing cotter pins.

√ √

Body

, Chassis, Safety Devices

Chassis,
Frame

Shall be free of cracks, deformation, or
corrosion.

√ √

Fastening bolts or nuts shall not be loose or
missing.

√ √ √

Body Panels

Shall be free of cracks, deformation, or
corrosion.

√ √

Doors and lids shall open, close, and lock
properly.

√ √

Fastening bolts or nuts shall not be loose or
missing.

√ √ √

Labels

Warning labels and instruction plates shall be
clean, legible, and free of damage.

√ √ √

Cutting System

Cutting
System

Blades shall be free of cracks or damage.

√ √ √

Page 71

Blade pins and wave washers shall be free
of cracks or damage.

√ √ √

Page 71

Cutting blade shield shall be free of cracks or
damage.

√ √ √

Skirts on cutting blade shield shall be free of
cracks or damage, and shall not be missing.

√ √ √

Belt tension shall be properly adjusted.

√ √ √

Page 74

Belt shall be free of damage or excessive
wear.

√ √ √

Page 74

When activated, mower brake shall stop
mower.

√ √ √

Page 75

Greasing points shall be properly greased.

√ √

Page 50,51

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды