CanyCom CMX 227 Скачать руководство пользователя страница 95

Страница: 95 / 103

-87-

Troubleshooting

• If any malfunction or abnormal condition is found, immediately stop using the machine

and take an appropriate measure according to the Troubleshooting chart below. If the
malfunction or abnormal condition is not listed in the chart, or the suggested measure
does not solve the problem, consult with your CANYCOM representative.

• Some corrective measures listed below require special knowledge and/or equipment.

Please contact your CANYCOM representative in such a case.

Area

Malfunction

Possible Cause

Corrective Measure

Ref.

Engine

Engine does not start, or

is difficult to start

Out of fuel.

→Fill fuel.

Page 17

Excessive fuel in the
engine.

→Wait a while and try

starting again.

Battery capacity is

insufficient.

→Add battery fluid.
→Charge battery.
→Replace battery.

Page 78
Page 78

Battery cable is
disconnected.

→Connect battery cable.

Insufficient or wrong oil.

→Fill or change oil.

Page 59

Dirty or damaged spark
plug.

→Clean or replace spark

plug.

Page 62

Other (other than the
above).

→Follow the instructions

"Starting"

to restart.

If problem persists,
please contact
your CANYCOM
representative.

Page 27

Oil pressure warning
light stays on

Insufficient amount of oil. →Fill oil.

Page 60

Other (other than the
above).

→Please contact

your CANYCOM
representative.

Engine stalls.

Out of fuel.

→Fill fuel.

Page 17

Choke valve closed.

→Open choke valve.

Other (other than the
above).

→Please contact

your CANYCOM
representative.

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Бренды по названию

Популярные бренды