CanyCom CMX 227 Скачать руководство пользователя

Страница: 74 / 103

Maintenance

-66-

5335M-0507-010E

HST Oil Tank

Filler Cap

1. Park the machine on a level ground.
2. Open the engine hood.

3. Unscrew and remove the filler cap.

Inspecting - Models with charge-pump

Upper Limit

Lower Limit

5347M-0507-010E

Filler Cap

Dipstick

1. Open the engine hood.

2. Remove the filler cap.
3. Fill the specified HST oil into the filler so that the oil level is between the upper and lower

limits on the dipstick.

4. Reinstall the filler cap back in place and screw it securely.

5. Close the engine hood.

Filling - Models with charge-pump

4. Wipe the dipstick with clean cloth. Reinstall

the filler cap and screw it fully.

5. Unscrew and remove the filler cap again.

Visually inspect that the oil level is between
the upper and lower limits on the dipstick. If it

is below the lower limit, fill oil.

6. Reinstall the filler cap and screw it fully.

7. Close the engine hood.

1. Open the engine hood.
2. Have an appropriate oil drain pan.

3. Remove the filler cap.

4. Remove the drain plug to drain the oil tank.

Changing - Models with charge-pump

• The HST system cannot be fully drained due

to its design.

• Do not operate the drive pedal or drive lever

with the HST oil drained. Doing so lets air
into the circuit, necessitating to bleed the
circuit.

NOTE

5347M-0507-030E

Oil Filter Cartridge

Drain Plug

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды