manualshive.com logo in svg

CanyCom CMX 227, Руководство оператора

Поделиться
Скачать
CanyCom CMX 227 Скачать руководство пользователя страница 72

Maintenance

-64-

5

Front Axle Oil (AWD models)

 • Oil to use and capacity: Page 49.

NOTE

5332M-0507-100E

Drain Plug

Knuckle

1.  Park the machine on a level ground.
2.  Have an appropriate oil drain pan.
3.  Remove the drain plug on the left front 

knuckle to drain oil.

4.   Remove the drain plug on the right front 

knuckle to drain oil as well.

Transmission Oil

 • Oil to use and capacity: Page 49.

NOTE

5332M-0507-040E

Drain Plug

Check Bolt

1.  Park the machine on a level ground.
2.  Have an appropriate oil drain pan.
3.  Remove the transmission oil drain plug to 

drain oil.

4.  Install the drain plug back in place.

Filler Cap

5347M-0507-020E

5.  Open the engine hood.

6.  Remove the transmission oil filler cap.

7.  Remove the check bolt.

8.   Fill the specified amount of correct oil into the 

filler, up to the check bolt hole.

9.  Put the check bolt back in place.

10.  Put the filler plug back in place.

11.  Close the engine hood.

 •  AWD Models: CMX227

NOTE

Содержание CMX 227








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды