CanyCom CMX 227 Скачать руководство пользователя

Страница: 78 / 103

Maintenance

-70-

1. Park machine on level ground.
2. Remove left step.

Adjusting Nut

Lock Nut

5347M-0507-071E

3. Loosen the lock nut
4. Adjust the brake with the adjusting nut

so that the brake does not drag when the
parking brake pedal is free.

5. Adjust the brake so that the brake works and

the parking brake pedal locks securely when
the parking brake lock lever is applied

6. Tighten the lock nut.

Rear Brake

• If the brake does not work even the parking

brake pedal is locked, the brake shoe is
worn out. Please contact your CANYCOM
representative for replacement.

• Always keep parking brake adjusted for maximum performance. Improperly

adjusted parking brake may result in property damage, serious injury, or death.

Parking Brake

Front Brake (AWD Models)

7. Lock the parking brake pedal and inspect

that the stretch of the spring is between 5mm
and 8mm. If it is not within this range, adjust
it with the adjusting nut.

8. Tighten the lock nut after adjustment
9. Install the left step back in place.

Adjusting Nut

Lock Nut

5347M-0507-101E

NOTE

• AWD Models: CMX227

NOTE

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды