CanyCom CMX 227 Скачать руководство пользователя

Страница: 82 / 103

Maintenance

-74-

• Never place any part of the body under the cutting blade shield when the mower

is running.

• Do not allow bystanders to come near the machine when inspecting the mower

drive belt.

Mower Drive Belt

• Adjust belt tension properly. The improperly tensioned belt may reduce

performance and its service life.

• The V-belt stretches (breaks in) when it is new. Inspect and adjust the V-belt after

the first day's (4 hours') use.

• For a longer service life, inspect and adjust (as necessary) the V-belt as the daily

pre-start up checks.

NOTE

1. Remove the engine hood, rear cover and

rear bumper.

2. Turn the mower clutch lever to [ON].
3. Inspect the condition of the V-belt to be free

of damages or wear. Replace if damaged or
worn. Contact your CANYCOM

representative for replacement.

Inspecting and Adjusting

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды