CanyCom CMX 227 Скачать руководство пользователя

Страница: 85 / 103

-77-

Maintenance

Mower Gearbox Oil

• Oil to use and capacity: Page49.

NOTE

Drain Plug

Oil Filler

5347M-0508-060E

1. Park the machine on a horizontal ground.
2. Move the cutting height adjust lever to the

lowest position.

3. Have an appropriate oil drain pan.
4. Remove the drain plug to drain gearbox oil.

• Removing the oil filler cap helps drain oil.

NOTE

5. Install the drain plug back in place.
6. Remove the filler cap and fill the specified

amount of correct oil into the filler.

• If it is difficult to reach to the filler, use an

oil jug or remove the seat and the plate
under the seat.

NOTE

7. Install the filler cap back in place and move

the cutting height adjust lever to the highest
position.

Turnbuckle

Lining

Lining Groove

Lock Nut

5347M-0508-050E

5. Move the mower clutch lever to [OFF].

6. Visually inspect if the lining is firmly in contact

with the lining groove on the pulley.

7. Shake the turnbuckle to see if there is some

play.

8. If the lining is not firmly in contact with the

groove, or the turnbuckle is too tight, readjust
the turnbuckle.

9. Move the mower clutch lever [ON] and [OFF]

several times, then perform checks 4 through
7. Adjust as necessary.

10. Reinstall the rear cover, engine hood, and

bumper.

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды