CanyCom CMX 227 страница 68 Скачать руководство пользователя

Страница: 68 / 103

Maintenance

-60-

Upper Limit

Lower Limit

5321M-0506-020E

5. Visually inspect the oil level. Make sure the

oil level is between the upper and lower
limits. If it is below the lower limit, add oil.

6. Visually inspect the condition of oil. If it is too

dirty or viscosity is not normal, change oil.

7. Put the dipstick back in place.
8. Close the engine hood.

5332M-0506-030E

Oil Filler Cap

Filling

1. Open the engine hood.

2. Remove the oil filler cap.

3. Fill specified amount of correct oil into the

filler.

4. Check the oil level. Make sure the oil level is

between the upper and lower limits.

5. Put the oil filler cap back in place.

6. Close the engine hood.

Changing

1. Have an appropriate oil drain pan.
2. Open the engine hood.

3. Remove the oil filler cap.

4.  Remove the drain plug to drain oil.
5.  Put the drain plug back in place.
6.  Fill oil.
7.  Check the oil level and make sure the  oil

level is appropriate.

8. Put the oil filler cap back in place.

9. Close the engine hood.

5347M-0506-040E

Drain Plug

Oil Drain Pan

5347M-0506-010E

Dipstick

1.  Park the machine on a level surface.
2. Open the engine hood.
3.  Pull out the dipstick and wipe it clean.
4.  Insert the dipstick fully and pull it out.

Inspecting

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды