CanyCom CMX 227 Скачать руководство пользователя страница 22

Страница: 22 / 103

Controls and Components

-14-

11 Cutting Height Adjust . . . . .

Cutting height adjust lever is used to adjust the cutting
height. Grab and hold the cutting height adjust lock and
move the cutting height adjust lever back or forth to adjust
the cutting height.

13 Mower Clutch Lever . . . . . .

Mower clutch lever is used to start or stop running the
mower.

14 Tilt Lever . . . . . . . . . . . . . . . .

Tilt lever is used to adjust the angle of the steering wheel.

15 Head Light Switch . . . . . . . .

Head light switch is used to turn on or off the head
light. When the main switch is on, the head light switch
illuminates.

16 Rear Light Switch . . . . . . . . .

Rear light switch is used to turn on or off the rear
light. When the main switch is on, the rear light switch
illuminates.

17 Fuel Gauge . . . . . . . . . . . . . .

Fuel gauge indicates the amount of fuel in the fuel tank.

18 Hour Meter . . . . . . . . . . . . . .

Hour meter indicates the cumulative total operating time of
the machine in 0.1 hour increments.

19 Oil Pressure Warning . . . . . .

Under normal condition, the oil pressure warning light goes

off once the engine starts. It is illuminated when a problem

with engine oil pressure is detected while the engine is
running.

20 Battery Off Switch . . . . . . . .

Minus circuit connection of the battery can be switched
on or off. Used for vehicle maintenance and long-term
storage.

12 Cutting Height Adjust

Lever

Lock

Light

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Бренды по названию

Популярные бренды