CanyCom CMX 227 Скачать руководство пользователя страница 47

Страница: 47 / 103

-39-

Operation

Working

Inspecting Cutting Blade

Inspect the cutting blades before work. Refer to

Cutting Blades

(page 71) for the inspection

procedure.

Adjusting Cutting Height

5347M-0403-010E

Cutting Height Lock

Cutting Height Adjust Lever

1. Grab the cutting height lock to unlock the

cutting height adjust lever.

5347M-0403-020E

Cutting Height Adjust Lever

2. With the cutting height lock pulled up, move

the cutting height adjust lever to a desired
position.

3. Release cutting height lock to lock the cutting

height adjust lever.

•  Cutting Height Range:
  0mm - 150mm

(CMX227, CM226)

• The cutting Height indicated on the side

of the cutting height adjust lever is for
reference purpose only; actual cutting
height may vary due to the condition of the
ground or brush and other factors.

NOTE

135

150

CMX227H CM226

Running

Stationary

5347M-5351-0403-100

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Бренды по названию

Популярные бренды