CanyCom CMX 227 Скачать руководство пользователя

Страница: 71 / 103

-63-

Maintenance

Drive Train

• Stop the engine and remove the ignition key when servicing the drive train.

• Allow the machine to cool off before servicing. An engine and its ancillaries are

very hot after operation and may pose a burn hazard.

Tires

• Inflate the tires to the specified pressure. Under- or over-inflation causes

uneven wear or other damages to the tires.

• Dispose of drained oil properly.

Tire Size

Pressure KPa(kgf/cm

)

Front Wheel

4.00-7 (4PR)

240 (2.4)

AGR 4.00-7 (2PR)

120(1.2)

Rear Wheel

17×8.00-8 (4PR)

240 (2.4)

5332M-0507-010E

Valve Cap

1.  Park the machine on a level ground.
2.  Remove the valve cap.
3.  Check the tire air pressure. If it is different

from the specified values, adjust the
pressure.

4. Put the valve cap back in place.

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды