CanyCom CMX 227 Скачать руководство пользователя

Страница: 80 / 103

Maintenance

-72-

Inspecting

5331M-0508-010E

New

Wear Limit

Blade Pin

Replace when either
of the part wears out

• Wear Limit
Blade: Up to the line connecting the outer

edge and the inner edge.

Blade Pin: Up to either of the shoulder.

NOTE

1. Open the cutting blade shield.
2. Visually inspect the blades and blade pins

for wear and damage. If the blades are worn
normally, turn them over and use. Replace if
both of the edges are worn. If the blades or
blade pins are worn excessively, deformed,
damaged, or missing, replace them with new
ones.

3. Inspect the cutting blade stay. If the stay is

worn excessively, deformed or damaged,
contact your CANYCOM representative and
have it replaced with a new one.

4. Close the cutting blade shield.

• Wear Limit: Up to the solid line in the

left figure (should have more than 15mm
clearance between the edge of the cutting
blade stay and mounting slot.)

NOTE

5347M-0508-080E

Blade

Rotating Direction

Flat Surfaces

Blade Pin

Wave Washer

Mounting, Dismounting Hole

Wear Area

Mounting Slot

Lug Hole

Cutting Blade Stay

Wear Area

Handle with care.
These parts may become sharp

5332M-0508-040E

15mm

When New

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды