CanyCom CMX 227 страница 100 Скачать руководство пользователя

Страница: 100 / 103

Transporting

-92-

• Park the transporter (truck, trailer) on a level ground. Always apply parking

brake and use chocks to secure the wheels.

• Do not allow bystanders to come close to the machine or the transporter when

loading or unloading the machine.

• Use only the loading ramps with sufficient strength (to withstand the combined

weight of the machine and the operator), width (more than twice the width of the
tire.), and length (more than 4 times the height of the bed of the transporter),
and have anti-slip ramp surfaces.

• Secure the hooks of the loading ramps firmly and flush with the bed.

• Move slowly forward when loading onto, and move slowly backward when

unloading off of the transporter. Pay special care when going over the joint
between the bed and the ramps; the machine may tip.

• Do not turn on the loading ramps. The machine may fall.

• Tie down the machine securely. Make sure the machine does not move around.

Hauling

Loading and Unloading

1. Park the transporter on a level ground. Apply parking brake of the transporter and

secure the wheels with chocks.

2. Place loading ramps. Secure hooks of ramps firmly and flush with the bed of the

transporter.

5332M-0701-010E

More than 4 times

the height

Height

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды