CanyCom CMX 227 Скачать руководство пользователя

Страница: 62 / 103

Maintenance

-54-

5332M-0401-140E

Front Cover

Clip

Rod

3. Raise the steering wheel to the maximum

angle and fit the clip on the back of the front

cover to the rod.

4. Fit the upper part of the front cover.

Removing and Installing Body Panels

• Cut or pinch hazard exists when removing or installing the body panels; beware

of the sharp edges and pinch points.

• Make certain to reinstall the panels after removing for repairs or inspection.

Front Cover

5347M-0401-110E

2. Pull up the front cover.

• A tool box is provided under the front

cover. Use this tool box to store tools or
replacement cutting blades.

NOTE

• Make sure not to catch the front cover with

the plate on both sides when installing the
front cover. If caught, it breaks the front
cover.

NOTE

1. Remove the knob bolts (2 places).
Pull the top side of the front cover to unlock

the latch.

5347M-0401-041E

Latch

Front Cover

Knob Bolts

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды