CanyCom CMX 227 Скачать руководство пользователя | Manualshive

Страница: 36 / 103

background image

Operation

-28-

4

5347M-0402-011E

Parking Brake Pedal

Parking Brake Lock Lever

1. Make certain the parking brake pedal is

depressed and locked. If it is not, depress
the parking brake pedal and pull the parking
brake lock lever to lock it.

• Safety feature: the engine cannot be

started unless the parking brake pedal is
depressed.

5347M-0402-021E

Mower Clutch Lever

2. Make sure the mower clutch lever is in [OFF]

position.

• Safety feature: the engine cannot be started

unless the mower clutch lever is in [OFF]
position.

5347M-0402-101E

Auxiliary
Transmission
Shift Lever

L

H

N

3. Make certain the auxiliary transmission shift

lever is in [N] (neutral) position.

NOTE

NOTE

• Do not use this machine in dusty places such as desert. Dust may clog the

air filter or enter the engine, which may result in loss of performance and an
accident. It also causes excessive wear.

• Do not use this machine in the altitude above 1500m (4920ft.) in its original

configuration. This machine cannot perform adequately above that altitude.
Using this machine under such conditions may result in an accident or cause
damage to machine. If you need to use this machine above that altitude, contact
your CANYCOM representative.

«
...
34
35
36
37
38
...
»

Содержание CMX 227








































































































Отзывы:

Нет отзывов

Похожие инструкции для CMX 227

Бренд: Feider Machines Страницы: 20

Бренд: Valloy Incorporation Страницы: 50

Бренд: Zenoah Страницы: 42

Бренд: Hypertherm Страницы: 270

Бренд: Niedax Страницы: 10

Бренд: IDEAL Страницы: 48

Бренд: Logan Страницы: 16

PLAN 100 Series

Бренд: Rapid-Air Страницы: 58

ClassicCut CL710

Бренд: Rexel Страницы: 30

Бренд: IVT Страницы: 88

Бренд: Stihl Страницы: 36

Бренд: HSGM Страницы: 8

Бренд: Talet Equipment Страницы: 20

Бренд: Zenoah Страницы: 68

Бренд: IDEAL Страницы: 48

Бренд: RASOR Страницы: 15

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды