CanyCom CMX 227 Скачать руководство пользователя

Страница: 93 / 103

-85-

Maintenance

• Do not wash the engine or control panel with running water; water may enter

inside and cause rust or damage.

• Clean the machine after use; dirt or foreign objects may freeze and cause

damage.

• Do not attempt to move the machine when it becomes inoperable due to

freezing

After Cold Weather Use

• Fire hazard; clean the machine of cut grass and similar material after use. Cut

grass that is accumulated on the machine can catch fire.

Clean the machine; wash off dirt, mud, and remove grass and other foreign materials

after use.

2. Park the machine on a paved or firm, dry surface, or on a bed of lumber.

3. If the machine is to be left outside, cover the machine with a protective, water-proof

covering after it is cooled off.

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды