CanyCom CMX 227 Скачать руководство пользователя

Страница: 45 / 103

-37-

Operation

Parking

• Always park on a firm, level place. Never park on a potentially dangerous place.

• Avoid parking on a slope. Never park on a slope with an incline of 10 degrees or

steeper. If it is absolutely necessary to park the machine on a slope less than 10

degrees, make certain to apply parking brake firmly and block the wheels with

chocks.

• Apply parking brake and remove the key when parking.

• Do not park near combustibles.

5347M-0402-200E

Throttle Lever

1. Stop the machine.
2. Move the throttle lever toward [ ] (slow) to

slow the engine speed.

5347M-0402-011E

Parking Brake Pedal

Parking Brake Lock Lever

3. Depress the parking brake pedal and pull the

parking brake lock lever to lock the parking
brake pedal in depressed position.

Содержание CMX 227








































































































Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды

CanyCom CMX 227, Руководство оператора

Результаты поиска

Содержание CMX 227

Отзывы:

Похожие инструкции для CMX 227

Бренды по названию

Популярные бренды