Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 4

Страница: 4 / 200

Malfunction......................................................................................................... 65

Though paper is loaded in the cassette, the display of the message "load paper of the drawer."

may occur due to the disconnection of the connector................................................................... 65

"The original scanning area is dirty." is displayed due to poor adjustment....................................... 67
"Place the originals again." is displayed after starting to copy with the copy board.......................... 70
The waste toner assembly cover does not open when the packing tape is removed....................... 72
The primary transfer roller drive coupling is coming off and breaking due to interfering with

the sheet metal of the main body...................................................................................................73

Breakage of the boss of the idler gear due to wrongly assembled pick-up roller.............................. 75
Toner leaking from the ITB cleaning unit due to coming off of waste toner gear holder may occur.. 76
Opening waste toner cover/ toner leakage due to the defect waste toner case................................77
The LCD control panel displays a blank screen due to the disconnection of the HDMI cable.......... 79
Safety cover coming off of Tray 1 due to the safety cover being pressed hard to the rear side

or downward (Saddle/Staple/Booklet/Finisher)..............................................................................81

Measures when paper is not stapled (corner/double) after installation (Inner Finisher-G1/H1/K1)...96

Noise/Odor..........................................................................................................98

Noise (grinding-like noise) from the right rear side of Main Body......................................................98
Noise (squeaking noise) from the right rear side of Main Body.......................................................101
After turning ON the main switch, Abnormal noise/the display of the message "Close the upper

right cover of the drawer. " may occur due to the disconnection of the connector...................... 103

The waste toner gear holder comes off due to the contact during setting the yellow developing

assembly......................................................................................................................................104

Abnormal noises/toner leaking from the ITB cleaning unit due to coming off of waste toner

gear holder ..................................................................................................................................107

Noise of tooth jump from the main drive assembly and blurred image due to gear mounting

position failure..............................................................................................................................112

Abnormal sound from the registration guide unit during feeding papers.........................................113
Abnormal (chirruping) noise of the second delivery drive assembly of the main unit due to

deformed gear............................................................................................................................. 115

Noise (an abnormal noise from meshing failure of tooth)/ toner soiling inside the machine /

stained images due to disengagement between gears in the waste toner drive assembly......... 118

Warning Message.............................................................................................120

"Replace Toner Cartridge" message is displayed on the initial installation or after replacing

the toner cartridge........................................................................................................................120

"Toner cart. may be malfunctioning" message displayed due to a bottle connector cable failure

message displayed due to a bottle connector cable failure.........................................................121

Jam (Main Unit)................................................................................................ 122

0107/0A07/010A/0A0A Jam code since harness is caught.............................................................122
0106/010B Jam Code due to the soiled duplex merging roller........................................................123
E514-0002/1C14 Jam code due to incorrect paper width of the aligning plate of the processing

tray unit ( Inner Finisher_G1 )......................................................................................................126

020A jam cord due to the deformed 2nd delivery upper guide........................................................131
0003 jam code due to the use of ADF under a high temperature environment...............................134

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Результаты поиска

Содержание imageRUNNER ADVANCE C3330 Series

Отзывы:

Canon imageRUNNER ADVANCE C3330 Series, Руководство по устранению неисправностей, Страница: 4 / 200

Результаты поиска

Содержание imageRUNNER ADVANCE C3330 Series

Отзывы: