Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 38

[Caution]
- If you perform the work in sleep mode or when the power is turned OFF during sleep mode, the Primary Transfer Roller will not
be disengaged.
When removing the Drum Unit (Bk), be sure to do so after returning the machine to a standby state.
- Since there is a risk of damaging the Photosensitive Drum, do not touch the surface.
- Be sure to block light to the removed Drum Unit using paper, otherwise it will be exposed to light.
3) Remove the screw [1].

4) Pull out the Developing Unit [1] up to the position [a]. Disconnect the connector [2] and put it in the groove [3] for the cover.
Pull out the Developing Unit while lifting it.

5) Check the surroundings of the Developing Unit.
If fluffy foreign matter is adhered around the Developing Unit sleeve [a], remove the foreign matter.
[Caution] When removing the foreign matter, be careful not to touch the surface of the sleeve.
If the Developing Unit sheet [a] is wavy, replace the Developing Unit.

33

«
...
36
37
38
39
40
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов