Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 58

[Caution]
- When the Width Adjustment is changed to this setting, small print may get difficult to read.
- Depending on the combination of used application and font, positive effect may not be gotten. (In the case of that the characters
cannot be recognized as text.)
[Reference] Width Adjustment is supported with MNcon Ver.6.32 onward.
A-6) Change the Advanced Smoothing
A-6-1) Select Settings/Registration > Function Settings > Printer > Printer Settings > Custom Settings > Print Quality > Advanced
Smoothing > Advanced Smoothing[1] and change to "Level 2" [2].
[Caution] When "Resolution" is set to "1200 dpi" or when "Halftones" is set to "Error Diffusion", this function is not enabled.

[Reference] If the setting is set from each PC, from the printer driver "Quality > Advanced Settings > Advanced Smoothing" is
changeable to "Level 3".

B) Referring to the correspondence table, determine where to change from among B-1) to B-3) for the image used in the user's
print out and change as needed, then go to the step 9).
B-1) Change the Density (Fine Adjust)
B-1-1) Select Settings/Registration > Function Settings > Printer > Printer Settings > Custom Settings > Print Quality > Density
(Fine Adjust) > Black [1].

[Reference]
- In Settings/Registration > Function Settings > Printer > Printer Settings > Custom Settings > Print Quality, only if Toner Save is
set to "OFF", Density (Fine Adjust) is available.
- If the setting is set from each PC, from the printer driver go to "Quality > Advanced Settings > Toner Density" and change "Printer
Default" to "Adjust", and then Density (Fine Adjust) in "Details... > Toner Density Details > Black" is changeable.

53

«
...
56
57
58
59
60
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов