manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Руководство по устранению неисправностей, Страница: 157 / 200

Поделиться
Скачать
Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 157

Copier Color | iR-ADV C3330/C3325/C3320 Series |

E280-000x, E302-000x, E315-0xxx, E732-0010 and E270-000x
caused by the fault of cable, flat

[Symptom]

In the machines prior to the Countermeasure cut-in serial number in factory described below Measure against E280-000x,
E302-000x, E315-0xxx, E732-0010 and E270-000x.
- E280-0001: Scanner Unit communication error. (Communication between the Main Controller and the Scanner Unit was not
started within the specified period of time.)
- E280-0002 : Scanner Unit communication error. (Disconnection of FFC between the Main Controller and the Scanner Unit was
detected.)
- E280-0003 : Scanner Unit communication error. (Reading or writing error was detected between the Main Controller and the
Scanner Unit.)
- E302-0001 : Shading error.( An error in the shading value was detected at white shading.)
- E302-0002 : Shading error.(An error in the shading value was detected at black shading.)
- E315-0007 : Image processing device error. (JBIG encode error was detected.)
- E315-0500 : Device timeout error.(An image synchronous signal from the Main Controller PCB to the Reader could not be
detected for 30 sec or longer.)
- E315-0510 : Device timeout error.(An image synchronous signal from the Main Controller PCB to the Reader could not be
detected for 30 sec or longer.)
- E732-0010 : Scanner communication error.(DDI-S communication error (Vsync detection error) was detected.)
- E270-0001 : Scanner Unit communication error. (The vertical scanning synchronous signal (VSYNC) was not transmitted
normally at the Scanner Unit side that communicates with the Main Controller PCB.)
- E270-0002 : Scanner Unit communication error. (The vertical scanning synchronous signal (VSYNC) was not transmitted due
to horizontal scanning synchronous signal (HSYNC) error which is sent to the Main Controller PCB.)

[Reference]

Previously it was difficult to identify cause for errors that occur due to broken flat cable since there are many errors available. To
make an improvement on the issue, a change in the software is made (MN-CONT V12.07 or later) so that E270-0002 is displayed
when the signal for broken flat cable is detected. (Refer to SI No.F01748)
The following Service Information can also be referred to as they are related to errors attributable to flat cable:
- When E280-0002 is displayed, as smoothness of the flat cable may be attributable to broken cable, the flat cable needs to be
replaced and a friction sheet needs to be attached. (Reference Service Information No.F00703)
- When E302-0001 is displayed, soiling on mirror is probably the cause, so the mirror needs to be cleaned. (Reference: Service
Information No.F01760)

[Cause]

There are 2 causes as below:
1.The terminals [1] of flat cable and the terminals [2] of connector are connected to the reader PCB. The terminals [2] are placed
on the terminals [1] and contacting as Figure [A].

When the dimensional accuracy for the flat cable is inadequate, terminals [1] and terminals [2] are off the correct positions and
contact at their sides as Figure [B] shows. If the products are shipped in this state, there may be no contacts of terminals [1] and

152

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов