Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 114

1) If waste toner has overflowed onto the Intermediate Guide, this waste toner can be fed into the Waste Toner Container by
operating the Waste Toner Feed Motor (M17) (COPIER > FUNCTION > PART-CHK > MTR = 14).
2) Fully open the Right Door.
3) Remove the ITB Unit.
4) Remove the Front Door.
5) Remove the Toner Bottle.
6) Remove the Drum Unit (Y).
7) Remove the Developing Unit (Y).
8) Remove the Left Cover (Upper).
9) Remove the First Delivery Tray.
10) Remove the Toner Bottle Mount.
11) Remove the Control Panel Lower Cover [1].
- 2 Screws [2]
- 2 Claws [3]

12) Release the 2 links [1] of the Bottle Motor.

[CAUTION] When installing the links of the Bottle Motor, be sure to pinch the Lock Arm [1].

109

«
...
112
113
114
115
116
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов