Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 49

Copier Color | iR-ADV C3330/C3325/C3320 Series |

White spots on high density image due to soiling of primary
charging roller

[Symptom]

When printing a large volume in high temperature/high humidity environment, white spots [a] may occur in high density area near
the edge of paper.
The arrow [b] indicates the direction of feeding.

[Cause]

Remaining toner attached on the drum [a] may pass the cleaning blade [c] and attach to primary charging roller [b]. If the remaining
toner attaches to primary charging roller, an abnormal discharge may occur from the primary charging roller to the drum.
The symptom tends to occur more when meeting both conditions below.
- Internal temperature of machine increased after continuous printing in high temperature/high humidity environment.
-An amount of remaining toner attached to the drum increased by printing high density images.

[Service work]

1) Select Settings/Registration > Adjustment/Maintenance > Maintenance > Clean Inside Main unit [1], and press "Start" button
[2].

44

«
...
47
48
49
50
51
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов