Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 109

Copier Color | iR-ADV C3330/C3325/C3320 Series |

The waste toner gear holder comes off due to the contact during
setting the yellow developing assembly.

[Symptom]

In the machines prior to the Countermeasure cut-in serial number in factory described below when inserting a yellow developing
assembly into a main unit, if it is inserted in left oblique direction, the waste toner gear holder may come off. If this happens, it
may let the waste toner leak and result in a stained image and the abnormal sound occur.

[Cause]

-

[Service work]

Insert a yellow developing assembly in straight direction into a main unit.

In the normal state of waste toner gear holder [A], the boss fits into the mounting hole [a]. Also the side of waste toner gear holder
and the flat surface of mounting part are set parallel to each other [b].
In the coming off state of waste toner gear holder [B], the boss does not fit into the mounting hole [c]. Also the side of waste toner
gear holder and the flat surface of mounting part are not set parallel to each other [d].

Check not only visually but also by grasping the waste toner gear holder to confirm that it does not rattle.

Install the removed waste toner gear holder as follows:
1) Insert the boss[a] on the upper part of the waste toner gear holder into the mounting hole[A] of the main unit, and fix the claw[b]
by hooking it on the edge of the plate[B].

104

«
...
107
108
109
110
111
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов