Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 86

Copier Color | imagePRESS C1 Series |
Copier Color | imagePRESS C800/C700/C60 Series |
Copier Color | imagePRESS C850/C750/C650 Series |
Copier Color | iR-ADV C2230/C2225/C2220 Series |
Copier Color | iR-ADV C3330/C3325/C3320 Series |
Copier Color | iR-ADV C5051/C5045/C5035/C5030 Series |
Copier Color | iR-ADV C5255/C5250/C5240/C5235 Series |
Copier Color | iR-ADV C7065/C7055 Series |
Copier Color | iR-ADV C7280/C7270/C7260 Series |
Copier Color | iR-ADV C9075PRO/C9070PRO/C9065PRO/C9060PRO Series |
Copier Color | iR-ADV C9280 PRO/C9270 PRO Series |

Safety cover coming off of Tray 1 due to the safety cover being
pressed hard to the rear side or downward (Saddle/Staple/
Booklet/Finisher)

[Symptom]

On the main bodies earlier than the following countermeasure cut-in serial numbers in factory, the safety cover [1] may come off
of Tray 1.

[Cause]

When the safety cover [1] is pressed hard to the direction of the arrow (rear side or downward), the above symptom occurs.

81

«
...
84
85
86
87
88
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов