manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Руководство по устранению неисправностей, Страница: 82 / 200

Поделиться
Скачать
Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 82

Copier Color | iR-ADV C3330/C3325/C3320 Series |

Opening waste toner cover/ toner leakage due to the defect waste
toner case

[Symptom]

In the machines prior to the Countermeasure cut-in serial number in factory described below The following symptoms may occur
in the waste toner container

• The tape that fixes the upper and lower sections of the waste toner container is lifted, and the waste toner leaks from the

gap made by the lifted tape.

• When opening and closing the cassette 1, the waste toner container flies out and the waste toner cover opens.

[Cause]

The above-mentioned symptoms are caused by the following reasons

• Since the tape that is attached to the waste toner container is so stiff that the tape is lifted.
• Since only small part of the claw of the waste toner container is hooked, it flies out.

[Service work]

When the above-mentioned symptoms occur, replace the waste toner container with a new type (WT-202) (FM1-A606-030).

[Service parts]

No.

 

Part Number

Description

1

Old

FM1-A606-020

CONTAINER, WASTE TONER, WT-202

New

FM1-A606-030

CONTAINER, WASTE TONER, WT-202

[Countermeasure cut-in serial numbers in factory]

Model

Serial number

iR-ADV C3330 AS 230V

QTZ02079

iR-ADV C3325 AS 230V

QUB01173

iR-ADV C3320 AS 230V

QUC02780

iR-ADV C3330 CN 220V

QUE00822

iR-ADV C3325 CN 220V

QUF00958

iR-ADV C3320 CN 220V

QUG02246

iR-ADV C3320L CN 220V

QUH02434

iR-ADV C3330 CN 220V G

TYT00503

iR-ADV C3325 CN 220V G

TYV00502

iR-ADV C3320 CN 220V G

TYX00512

iR-ADV C3330i EUR 230V

QTF06129

iR-ADV C3325i EUR 230V

QTS11319

iR-ADV C3320i EUR 230V

QTT10023

iR-ADV C3320 EUR 230V

QTU00964

iR-ADV C3330 IND 230V

RJS00576

iR-ADV C3325 IND 230V

RJU00582

iR-ADV C3320 IND 230V

RJV01657

iR-ADV C3330 KR 220V

QUJ00852

iR-ADV C3325 KR 220V

QUK03506

iR-ADV C3320 KR 220V

QUL02000

iR-ADV C3330i LTN 230V

RJQ00722

iR-ADV C3325i LTN 230V

RJR00758

iR-ADV C3330 TW 120V

QUM00501

iR-ADV C3325 TW 120V

QUN00501

iR-ADV C3320 TW 120V

QUP00501

iR-ADV C3330i US 120V G

QTX00507

iR-ADV C3330i US 120V

QTV04753

77

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов