manualshive.com logo in svg

Canon imageRUNNER ADVANCE C3330 Series, Руководство по устранению неисправностей, Страница: 126 / 200

Поделиться
Скачать
Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 126

Copier Color | iR-ADV C3330/C3325/C3320 Series |

"Toner cart. may be malfunctioning" message displayed due to a
bottle connector cable failure message displayed due to a bottle
connector cable failure

[Symptom]

" Toner cart. may be malfunctioning " message [A] may appear on the UI of the engine.

[Cause]

When the harness (bottle connector cable) between the DC controller PCB (J135) and the new/old bottle sensor interferes with
the metal sheet [A] of DC controller PCB, no communication can be made with the new/old bottle sensor, resulting in the above
symptom.

[Service work]

1) Remove 2 screws and then remove the cover (Rear upper).
2) Check a condition of the bottle connector cable. If the bottle connector cable interferes with the metal sheet of DC controller
PCB, wrap insulation tape around the bottle connector cable where interfering occurs.
If insulation tape is not available, work on the wiring so that the bottle connector cable does not interfere with the metal sheet of
DC controller PCB.
If the outer cover of the bottle connector cable is damaged, prepare a new bottle connector cable (FM1-D853-000) and replace
the old one.
3) Attach the cover (Rear upper) with the 2 screws.
4) Start the main body and confirm that the symptom does not occur.
If the symptom does not improve, check other causes.

[Service part] FM1-D853 CABLE, BOTTLE CONNECTOR

121

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов