Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 139

Copier Color | iR-ADV C3330/C3325/C3320 Series |
Copier Color | iR-ADV C2230/C2225/C2220 Series |
Copier Color | iR-ADV C5255/C5250/C5240/C5235 Series |

0003 jam code due to the use of ADF under a high temperature
environment

[Symptom]

In the machines prior to the Countermeasure cut-in serial number in factory described below 0003 jam may occur when ADF is
used under a high temperature environment.
- 0003: Registration sensor delay jam.

[Cause]

Some play is placed between the rib [a] and the rib [b] that supports the empty sensor lever [1] to allow a smoother sliding of the
empty sensor lever [1].
However the empty sensor lever expands due to heat under a high temperature environment, therefore the play may be lost if
the dimensions of the ribs are inadequate. If the play is lost, the smooth sliding of the empty sensor lever is obstructed and results
in the above mentioned symptom.

[Service work]

When the aforementioned symptom has occurred, prepare and replace with the new type empty sensor lever (FC9-4971-020)
following the procedure below.
1) Open the feeder cover [1].

2) Remove the pickup roller assembly.

134

«
...
137
138
139
140
141
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов