Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 200

Canon imageRUNNER ADVANCE C3330 Series Скачать руководство пользователя страница 70

Malfunction

Copier Color | iR-ADV C3330/C3325/C3320 Series |

Though paper is loaded in the cassette, the display of the message
"load paper of the drawer." may occur due to the disconnection
of the connector.

[Symptom]

The message "Load paper" may be displayed (a) on UI screen of the main body with the paper loaded in the cassette.

[Cause]

The size detection switches attached to each cassette detects paper size and whether paper is loaded in the cassette or not. If
any connector of the following cassettes is disconnected, the size detection switch will not be turned on even when the cassette
is inserted and the device regards it as the cassette is not inserted and displays the message "Load paper".
- Cassette 1:J1222 of Cassette 1 Size Switch [a]
- Cassette 2:J1221 of Cassette 2 size switch A [b]

- Cassette 3:J1136 of Cassette 3 size switch A [c] and J603 of Deck driver PCB [d] of the back side of the cassette pedestal
- Cassette 4:J1139 of Cassette 4 size switch A [e]

[Service work]

65

«
...
68
69
70
71
72
...
»

Содержание imageRUNNER ADVANCE C3330 Series









































































































































































































Отзывы:

Нет отзывов