Canon imageRUNNER ADVANCE 6055 Series, Руководство по обслуживанию

Страница: 899 / 1406

8
8
8-117
8-117
Service Mode > COPIER > OPTION > FNC-SW
Service Mode > COPIER > OPTION > FNC-SW
OPTION
■ FNC-SW
COPIER > OPTION > FNC-SW
PO-CNT ON/OFF of potential control function
Lv.1 Details To set ON/OFF of potential control function.
Use case When replacing the Potential Sensor
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to set the value back to 1 (ON) after servicing.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
PO-CNTMD Set potential control execution timing
Lv.2 Details To set the combination of timing to execute the potential control.
Use case When productivity decreases at execution of potential control
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 2
0:
• At warm-up rotation performed first time for the day in an HH
environment
• At last rotation in the case that a job right after startup first time for
the day takes 10 minutes or longer
• At last rotation after 1500 sheets since the last potential control
• At last rotation of the first job after 90 minutes since the last
potential control
• At warm-up rotation of the fist job after 10 minutes since the
startup first time for the day (30 seconds)
1:
• At warm-up rotation performed first time for the day in an HH
environment
• At last rotation in the case that a job right after startup first time for
the day takes 10 minutes or longer
• At last rotation after 1500 sheets since the last potential control
• At warm-up rotation of the fist job after 10 minutes since the
startup first time for the day (30 seconds)
2:
• At warm-up rotation performed first time for the day in an HH
environment
• At last rotation after 1500 sheets since the last potential control
Default value 0
COPIER > OPTION > FNC-SW
MODEL-SZ Fixed magnifictn & DADF orgnl dtct size
Lv.1 Details To set the fixed magnification ratio display and the original detection
size with DADF.
It is set automatically at the time of installation of the Reader
according to the location.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: AB configuration (6R5E) for Japan, 1: Inch configuration (5R4E)
for North/Middle/South America, 2: A configuration (3R3E) for
Europe, 3: AB/Inch configuration (6R5E) for Asia, Oceania, South
America
Default value It differs according to the location.
SCANSLCT ON/OFF of scan area calculate function
Lv.2 Details To set ON/OFF of the function to calculate scanning area from the
specified paper size.
When the paper size is larger than the original size, selecting ON
reduces productivity because the scanning area gets larger.
Use case When matching the scanning area with the paper size
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF (calculated from the detected original size)
1: ON (calculated from the specified paper size)
Default value 0
SENS-CNF Setting of original detection size
Lv.2 Details To set original detection size according to AB configuration/Inch
configuration/A configuration.
Select 1 (Inch configuration) for Inch configuration/A configuration
machine.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: AB configuration, 1: Inch configuration
Default value 0