Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 3

Страница: 3 / 119

Contents

Preface...........................................................................................................................................................................................................................................................................................7

Document conventions..............................................................................................................................................................................................................................................7

Brocade customers........................................................................................................................................................................................................................................... 8
Brocade OEM customers..............................................................................................................................................................................................................................9

Document feedback....................................................................................................................................................................................................................................................9

About This Document.......................................................................................................................................................................................................................................................... 11

Overview.....................................................................................................................................................................................................................................................................................13

Hardware features.......................................................................................................................................................................................................................................................13

ICX 7250 models..............................................................................................................................................................................................................................................13
Network and management interfaces................................................................................................................................................................................................... 14

Installation................................................................................................................................................................................................................................................................................ 23

Preparing the installation site.............................................................................................................................................................................................................................. 25

Installing the device.................................................................................................................................................................................................................................................. 26

Connecting devices in a traditional stack..................................................................................................................................................................................................... 59

Powering on the system........................................................................................................................................................................................................................................62

Installing the EPS4000 ..................................................................................................................................................................................................................................................63

EPS4000 external power supply.................................................................................................................................................................................................................... 63

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды