Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 33

Страница: 33 / 119

Attaching the extension brackets to the device

Complete the following steps to attach the extension brackets to the device. There are medium and long extension brackets that you can
use for this step. Choose the correct extension bracket for the depth of your rack.

Select the proper length extension bracket for your rack depth.

2. Position the right extension bracket along the side of the device as shown in

Figure 16

3. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the extension bracket and then into the holes

on the side of the device. Use the upper and lower screw holes, leaving the center holes empty.

4. Repeat

Step 1

and

Step 2

to attach the left extension bracket to the left side of the device.

5. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 16 Attaching the extension brackets to the device

Bracket extensions

Screws, 8-32 x 5/16-in., flathead Phillips

Installing the device in the rack

Complete the following steps to install the device in the rack.

Position the device in the rack, as shown in

Figure 17

, providing temporary support under the device until the rail kit is secured

to the rack.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды