Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 119

background image

The

value

variable is the temperature warning level, in Celsius. You cannot set this level higher than the maximum value allowed by your

device. The temperature warning level must be at least five degrees Celsius less than the temperature shutdown level, which is
automatically set by the device.

The following console and syslog message is displayed when the temperature reaches the warning level:

!!! Temperature is over warning level on stack unit 1!!!

Changing the temperature poll time

By default, the software polls the temperature sensor every 60 seconds to get the current temperature. This poll rate is controlled by the
device poll time, which also controls how often the software polls other system components.

To change the poll time, enter the chassis poll-time

value

command at the global configuration level.

device(config)# chassis poll-time 200

The

value

variable can be from 0 through 65535 seconds.

Displaying CPU usage

You can display the amount of the CPU in use. To do so, enter the show cpu command at any level of the CLI.

device# show cpu

20 percent busy, from 318 sec ago

1 sec avg: 2 percent busy

5 sec avg: 1 percent busy

60 sec avg: 1 percent busy

300 sec avg: 1 percent busy

Removing MAC address entries

You can remove the following types of learned MAC address entries from the system MAC address table:

∙

All MAC address entries

∙

All MAC address entries for a specified Ethernet port

∙

All MAC address entries for a specified VLAN

∙

A specified MAC address entry in all VLANs

For example, to remove entries for the MAC address 00-00-00 in all VLANs, enter the following command at the privileged EXEC
level of the CLI.

device# clear mac-address 00-00-00

Syntax: clear mac-address [

mac-address

| ethernet

port-num

| vlan

number

]

If you enter the clear mac-address command without any parameters, the software removes all MAC entries.

Use the clear mac-address

mac-address

command to remove a specified MAC address from all VLANs. Specify the MAC address in

the following format:

HHHH

.

HHHH

.

HHHH

.

Use the clear mac-address ethernet

port-num

command to remove all MAC addresses for a specified Ethernet port.

Use the clear mac-address vlan

number

command to remove all MAC addresses for a specified VLAN.

Managing an ICX 7250 Device

Brocade ICX 7250 Switch Hardware Installation Guide

96

53-1003898-02

«
...
94
95
96
97
98
...
»

Содержание ICX 7250
























































































































Отзывы:

Нет отзывов

Похожие инструкции для ICX 7250

Бренд: Magnetrol Страницы: 12

Бренд: Magnetrol Страницы: 24

Бренд: Radial Engineering Страницы: 12

Бренд: Edimax Страницы: 2

ZigBee Mini Hub

Бренд: ORVIBO Страницы: 3

Бренд: Vega Страницы: 28

Бренд: TRENDnet Страницы: 11

Бренд: ATEN Страницы: 2

Бренд: N-Tron Страницы: 158

Draco tera compact 480 Series

Бренд: Ihse Страницы: 244

Бренд: Homefibre Страницы: 2

IES2100SL Series

Бренд: 3onedata Страницы: 3

Ethernet Networks and Web Management

Бренд: GarrettCom Страницы: 12

IBPO-HB50SR-XFP

Бренд: Net Optics Страницы: 53

Personal MiniHub

Бренд: Black Box Страницы: 22

Бренд: PIKA Страницы: 7

QSW-4600 Series

Бренд: QTech Страницы: 58

Бренд: PCB Piezotronics Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды