Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 31

Страница: 31 / 119

FIGURE 14 Rack kit parts

Front brackets (2)

Bracket extensions (2)

Rear brackets, short (2)

Rear brackets, medium (2)

Rear brackets, long (2)

Screw, 8-32 x 5/16-in., panhead Phillips (8)

Screw, 8-32 x 5/16-in., flathead Phillips (16)

Screw, 6-32 x 1/4-in., panhead Phillips (8)

Screw, 10-32 x 5/8-in., panhead Phillips (8)

10.

Retainer nut, 10-32 (8)

Flush-front mounting the device in the rack

CAUTION
The device must be turned off and disconnected from the fabric during this procedure.

NOTE
The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 1.5U or 2U device.
The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

Attaching the front brackets

on page 46

Attaching the extension brackets to the device

on page 47

Installing the device in the rack

on page 48

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды