Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 37

Страница: 37 / 119

FIGURE 20 Attaching the rear brackets to the rack posts

Screws, 10-32 x 5/8-in., panhead Phillips

Retainer nuts, 10-32

Flush-rear (recessed) mounting the device in the rack

The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are reversed on the device.

CAUTION
The device must be turned off and disconnected from the fabric during this procedure.

NOTE
The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 1.5U or 2U device.
The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

Attaching the front brackets to the rear of the device

on page 51

Attaching the extensions to the front of the device

on page 52

Installing the device in the rack

on page 53

Attaching the rear brackets to the extensions at the front of the device

on page 54

Attaching the rear brackets to the front rack posts

on page 56

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды