Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 119

background image

Installation requirements

Provide space in an EIA rack with the following minimum and maximum distances between the front and back posts.

NOTE
For 1U and 2U devices, two people are required to install the device in a rack. One person holds the device, while the other
screws in the front and rear "L" brackets.

TABLE 8 Space requirements

Chassis with port-side
side vents

Notes

Chassis depth

Minimum rack depth

Maximum rack depth

No

Applicable to port-side and nonport-side flush
mounts.

L

L-12.7 cm (L-5 in.)

81.28 cm (32 in.)

Yes

Applicable to port-side flush mounts.

L

L-12.7 cm (L-5 in.)

81.28 cm (32 in.)

Yes

Applicable to nonport-side flush mounts.

L

L

81.28 cm (32 in.)

Note that if chassis depth (L) is less than 40.64 cm (16 in.), the chassis will not fit into a rack with a maximum depth of 81.28 cm (32 in.)
using the universal four-post rack kit. The maximum rack depth for a chassis less than 40.64 cm (16 in.) is 81.28 cm (32 in.) minus the
difference between the chassis depth and 40.64 cm (16 in.). For example, a chassis with a depth (L) of 35.56 cm (14 in.) is 5.08 cm (2 in.)
smaller than 40.64 cm (16 in.), so it will install into a rack with a maximum depth of 81.28 cm (32 in.) - 5.08 cm (2 in.) = 76.2 cm (30 in.).

Review the installation and facility requirements for your product before mounting the device . Refer to the

Hardware Installation Guide

for your product for more information.

Time and items required

Allow 15 to 30 minutes to complete the installation.

The following items are required to install the device using the Universal Four-Post Rack Kit:

∙

#2 Phillips torque screwdriver

∙

1/4-inch slotted-blade torque screwdriver

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

44

53-1003898-02

«
...
42
43
44
45
46
...
»

Содержание ICX 7250
























































































































Отзывы:

Нет отзывов

Похожие инструкции для ICX 7250

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 139

CoreBuilder 7000

Бренд: 3Com Страницы: 150

CoreBuilder 7000

Бренд: 3Com Страницы: 264

Бренд: 3Com Страницы: 574

Бренд: 3Com Страницы: 333

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 70

OfficeConnect 3C16790C

Бренд: 3Com Страницы: 18

Бренд: 3Com Страницы: 1314

SuperStack II Switch 1100

Бренд: 3Com Страницы: 62

Бренд: KELCO Страницы: 2

Бренд: Camozzi Страницы: 2

1big Dock SSD Pro

Бренд: LaCie Страницы: 28

Бренд: Manhattan Страницы: 2

tecatlantis EASY LED CONTROL 2 PLUS

Бренд: Aquatlantis Страницы: 4

DigiTOOLS VS-41USB

Бренд: Kramer Страницы: 8

TK-205K - PS/2 KVM Switch

Бренд: TRENDnet Страницы: 11

Бренд: GarrettCom Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды