Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 32

Страница: 32 / 119

Attaching the rear brackets to the extensions

Attaching the rear brackets to the rack posts

on page 50

Attaching the front brackets

Complete the following steps to attach the front brackets to the device.

Position the right front bracket with the flat side against the right side of the device at the front of the device, as shown in

Figure

2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side

of the device. Use the upper and lower screw holes, leaving the center holes empty.

3. Repeat

Step 1

and

Step 2

to attach the left front bracket to the left side of the device.

4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 15 Attaching the front brackets

Device

Front brackets

Screws, 8-32 x 5/16-in., flathead Phillips

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды