Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 53

Страница: 53 / 119

FIGURE 34 Attaching the bracket extensions to the device

Extension brackets

Screws, 8-32 x 5/16-in., flathead Phillips

Installing the device in the rack

Complete the following steps to install the device in the rack.

Position the device in the rack, as shown in

Figure 35

, providing temporary support under the device until the rail kit is secured

to the rack.

2. Attach the right front bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use

the upper and lower holes in the bracket.

3. Attach the left front bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the

upper and lower holes in the bracket.

4. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды