manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Поделиться
Скачать
Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 95

Displaying the temperature

To display the temperature of a device, enter the show chassis command at any level of the CLI. The show chassis command displays
the current temperature, the power supply status, and temperature threshold levels.

NOTE
The displayed temperature reflects the temperature of the board inside the device.

device# show chassis

The stack unit 1 chassis info: 

Power supply present, status ok

Sensor B Temperature Readings:

      Current temperature : 55.0 deg-C

Sensor A Temperature Readings:

      Current temperature : 50.0 deg-C

      Warning level.......: 71.0 deg-C

      Shutdown level......: 105.0 deg-C

Boot Prom MAC : 748e.f8ea.0360

Management MAC: 748e.f8ea.0360

=====

Displaying syslog messages for temperature

The software sends a syslog message and an SNMP trap if the temperature crosses the warning or shutdown thresholds. If you have
configured the device to use a syslog server or SNMP trap receiver, refer to the documentation for the server or receiver.

To display the system log, enter the show log command at any CLI level.

device# show log 

Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)

Buffer logging: level ACDMEINW, 20 messages logged

level code: A=alert C=critical D=debugging M=emergency E=error

                I=informational N=notification W=warning

Static Log Buffer:

1d02h07m29s:A:System: Stack unit 1 Temperature 60.0 C degrees, warning level 55.0 C degrees, shutdown level 

65.0 C degrees

1d02h07m29s:W:System: Temperature is over warning level on unit 1

Dec  1 10:16:34:A:System: Stack unit 2 Temperature 46.0 C degrees, warning level 70.0 C degrees, shutdown 

level 80.0 C degrees

Dec  1 10:16:34:A:System: Temperature on Unit 2 is over shutdown level, system is going to be reset in 2 

seconds

Dynamic Log Buffer (50 lines):

0d00h00m53s:I:STP: VLAN 1 Port 1/2/2 Bridge TC Event (FwdDlyExpiry)

0d00h00m53s:I:STP: VLAN 1 Port 1/2/2 STP State -> FORWARDING (FwdDlyExpiry)

0d00h00m37s:I:STP: VLAN 1 Port 1/2/2 STP State -> LEARNING (FwdDlyExpiry)

0d00h00m26s:I:STP: VLAN 1 Port 1/2/3 STP State -> FORWARDING (FwdDlyExpiry)

0d00h00m26s:I:STP: VLAN 1 Port 1/1/1 STP State -> FORWARDING (FwdDlyExpiry)

0d00h00m24s:I:STP: VLAN 1 Port 1/2/3 STP State -> LEARNING (FwdDlyExpiry)

0d00h00m24s:I:STP: VLAN 1 Port 1/1/1 STP State -> LEARNING (FwdDlyExpiry)

0d00h00m23s:I:STP: VLAN 1 Port 1/2/4 STP State -> BLOCKING (MakeBlking)

0d00h00m22s:I:System: Interface ethernet 1/2/4, state up

0d00h00m22s:I:STP: VLAN 1 Port 1/2/4 STP State -> LISTENING (MakeFwding)

0d00h00m22s:I:System: Interface ethernet 1/2/3, state up

Changing the temperature warning level

To change the temperature at which the device sends a syslog message and an SNMP trap, enter the temperature warning 

stack-id

value

 command at the privileged EXEC level of the CLI.

device# temperature warning 1 82

The 

stack-id

 variable can be a value from 1 through 12.

Managing an ICX 7250 Device

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

95

Содержание ICX 7250
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды