Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 26

Страница: 26 / 119

∙

Airflow: Be sure that the airflow direction for all equipment in a rack is the same or consistent.

∙

Mechanical loading: Do not place any equipment on top of a rack-mounted unit.

∙

Circuit overloading: Be sure that the supply circuit to the rack assembly is not overloaded.

∙

Grounding: Rack-mounted equipment should be properly grounded.

Installing the device

You can install the device on a desktop, the wall, or in an equipment rack.

DANGER

Mount the devices you install in a rack as low as possible. Place the heaviest device at the bottom and progressively place
lighter devices above.

Desktop installation

Complete the following steps to install the ICX 7250 device on a desktop or other flat surface. The device you are installing might look
different than the one in the following illustration.

DANGER

This equipment is suitable for mounting on concrete or other noncombustible surfaces only.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды